2Embedcom announces that a new firmware version (2.6.3) for Falcom Mambo2 devices is now available to download for our customers.

• New GUI (Graphical User Interface)
• New BIOS version 5.0.8
• Added new Loop alarm PFAL commands - Sys.AlarmLoop.Start[Stop]
• Left and right keys on the MAMBO2 are swappable by PFAL command Display.Button.Swap
• When receiving a new message an envelop symbol will be shown on the screensaver
• Added an additional parameter for incoming spy calls for example: GSM.Voicecall.eIncoming="spy"
• Added new value for the event IEEE.Device.eIndoor="" - set =0 for no devices found
• Erasing of AGPS data can be done by executing the PFAL command $PFAL,Sys.Device.FactoryReset
• Increased phone book entries. Up to 100 phone book entries are now supported
• Battery Low Alarm/Screen will automatically be closed when applying power to the device
• Decreased the length of the beep tone at device start and shutdown
• New user symbols in the range from 40..43 with corresponding events DISPLAY.User.e
• Added new states for the tilt function Display.tilt.sState={deactivated, activated}
• Saving settings of the tilt function after calibrating the device
• Added new states for the GPS time and date span gps.time.sLocaltimeSpan and  gps.time.sLocalDatespan
• Added new  dynamic entry &(TXT_ID:XXXX), for showing strings from the device language resources
• Erasing of the configuration settings during the start up process by pressing the Left and Right keys on the MAMBO2 at the same time for longer than 10 seconds.
• Added new state GSM.VoiceCall.sNotReady
• Added new event Display.Follow.eSelect - Occurs when the user selects a device to be traced with the specified ID
• Added new event Display.Follow.eDest - Occurs when the destination of the tracing device is reached
• Added new configuration parameter GPS.TRACE.DEV=""
• Added new state for the Tilt function Display.Tilt.sCounter - Defines how many times the event "IO.Bearing.e6" should be occurred before this Tilt state is set to True without the device goes back to the calibrated position
• New PFAL command Display.Button.{enable,disable,navigation} - enables/disables the Left and Right and 5-way navigation buttons for navigating and using the menus on the MAMBO2-UXFS screen.
• Added new configuration parameter DISP.MESSAGE.PROT - Defines protocols to be reported as an answer to the server-related M-Box messages.
• Extended PFAL command Display.Message - Contains also up to 4 possible answers to the received message
• Added new configuration parameter for the Tilt function MOTION.TILT
• Added new PTI Option with the corresponding event IO.Motion.ePTI for the Power Mode Doze
• Wake up from the Doze mode due to the Motion as an extention option
• Added new configuration parameter for reading SMS during an active voice call
• Temporary entering of the PIN code through the GUI.
• Added new configuration which defines the time, in milliseconds, the device must wait before launching the screen saver DISP.SAVER=1,10000
• Calculating the trip-distance and trip-high using the PFAL-Command GPS.Nav.TripCalc
• Added new dynamic entries &(LocalTime) and &(LocalDate)
• Added new Trip event DISPLAY.Trip.e={start,stop,...}
• Added new configuration parameter for ANT Speed sensor DEVICE.BIKESPEED.CIRCUM
• The index of the images for the phone book entries range from 301 to 399
• Added new configuration parameter TCP.CLIENT.LOGIN.EXT="" - for storing user text
• Added SLIDING Mode
• Added new Trip state - Display.Trip.s={inactive,active}
• Added new state for the Trip mode - Display.Tripmode.s={walk, bicycle,  motor}
• Added new dynamic entries for the ANT Sensors &(Cadence), &(BikeSpeed), &(BikeDistance) and &(ANTRaw)
• Added new PFAL Command - TCP.Client.CleanBuffer
• Once ANT Sensors are connected to the MAMBO2 device, their data will be saved in to the FLASH memory. On the next device start only these sensors will be searched
• Added new dynamic entry &(PVbat) - reports battery charge level in percent (%).
• Added new configuration parameter for the Motion Falling MOTION.FALLING

Not supported PFAL-Commands and dynamic entries:

• Display.sliding.disable
• Display.sliding.enable
• Display.saver.disable
• Display.saver.enable
• Sys.Device.ClearAlarm
• Sys.GSM.Powermode
• GPS.Nav.Static
• GPS.Nav.SBAS
• Display.Show
• Display.PeMenu
• &(AlarmText)

Optimization:

• Swapping keys works for all views
• Volume may be modified also during an active voice call
• Improved SIM card detection
• Restarting only GPS receiver when updating AGPS data into the MAMBO2 device
• Turning off the speaker when detecting a Spy Call
• Key events are always generated when the device wakes up from Doze mode

Downloads:

• Firmware and Release Notes
• User manual