Nueva versión de firmware 2.6.3 para Mambo2

2Embedcom anuncia que la nueva versión de firmware (2.6.3) para dispositivos Mambo2 de Falcom ya está disponible para descarga para nuestros clientes.

Este nuevo firmware incorpora las siguientes mejoras:

New GUI (Graphical User Interface)
New BIOS version 5.0.8
Added new Loop alarm PFAL commands - Sys.AlarmLoop.Start[Stop]
Left and right keys on the MAMBO2 are swappable by PFAL command Display.Button.Swap
When receiving a new message an envelop symbol will be shown on the screensaver
Added an additional parameter for incoming spy calls for example: GSM.Voicecall.eIncoming="spy"
Added new value for the event IEEE.Device.eIndoor="" - set =0 for no devices found
Erasing of AGPS data can be done by executing the PFAL command $PFAL,Sys.Device.FactoryReset
Increased phone book entries. Up to 100 phone book entries are now supported
Battery Low Alarm/Screen will automatically be closed when applying power to the device
Decreased the length of the beep tone at device start and shutdown
New user symbols in the range from 40..43 with corresponding events DISPLAY.User.e
Added new states for the tilt function Display.tilt.sState={deactivated, activated}
Saving settings of the tilt function after calibrating the device
Added new states for the GPS time and date span gps.time.sLocaltimeSpan and gps.time.sLocalDatespan
Added new dynamic entry &(TXT_ID:XXXX), for showing strings from the device language resources
Erasing of the configuration settings during the start up process by pressing the Left and Right keys on the MAMBO2 at the same time for longer than 10 seconds.
Added new state GSM.VoiceCall.sNotReady
Added new event Display.Follow.eSelect - Occurs when the user selects a device to be traced with the specified ID
Added new event Display.Follow.eDest - Occurs when the destination of the tracing device is reached
Added new configuration parameter GPS.TRACE.DEV=""
Added new state for the Tilt function Display.Tilt.sCounter - Defines how many times the event "IO.Bearing.e6" should be occurred before this Tilt state is set to True without the device goes back to the calibrated position
New PFAL command Display.Button.{enable,disable,navigation} - enables/disables the Left and Right and 5-way navigation buttons for navigating and using the menus on the MAMBO2-UXFS screen.
Added new configuration parameter DISP.MESSAGE.PROT - Defines protocols to be reported as an answer to the server-related M-Box messages.
Extended PFAL command Display.Message - Contains also up to 4 possible answers to the received message
Added new configuration parameter for the Tilt function MOTION.TILT
Added new PTI Option with the corresponding event IO.Motion.ePTI for the Power Mode Doze
Wake up from the Doze mode due to the Motion as an extention option
Added new configuration parameter for reading SMS during an active voice call
Temporary entering of the PIN code through the GUI.
Added new configuration which defines the time, in milliseconds, the device must wait before launching the screen saver DISP.SAVER=1,10000
Calculating the trip-distance and trip-high using the PFAL-Command GPS.Nav.TripCalc
Added new dynamic entries &(LocalTime) and &(LocalDate)
Added new Trip event DISPLAY.Trip.e={start,stop,...}
Added new configuration parameter for ANT Speed sensor DEVICE.BIKESPEED.CIRCUM
The index of the images for the phone book entries range from 301 to 399
Added new configuration parameter TCP.CLIENT.LOGIN.EXT="" - for storing user text
Added SLIDING Mode
Added new Trip state - Display.Trip.s={inactive,active}
Added new state for the Trip mode - Display.Tripmode.s={walk, bicycle, motor}
Added new dynamic entries for the ANT Sensors &(Cadence), &(BikeSpeed), &(BikeDistance) and &(ANTRaw)
Added new PFAL Command - TCP.Client.CleanBuffer
Once ANT Sensors are connected to the MAMBO2 device, their data will be saved in to the FLASH memory. On the next device start only these sensors will be searched
Added new dynamic entry &(PVbat) - reports battery charge level in percent (%).
Added new configuration parameter for the Motion Falling MOTION.FALLING

Not supported PFAL-Commands and dynamic entries:

Display.sliding.disable
Display.sliding.enable
Display.saver.disable
Display.saver.enable
Sys.Device.ClearAlarm
Sys.GSM.Powermode
GPS.Nav.Static
GPS.Nav.SBAS
Display.Show
Display.PeMenu
&(AlarmText)

Optimization:

Swapping keys works for all views
Volume may be modified also during an active voice call
Improved SIM card detection
Restarting only GPS receiver when updating AGPS data into the MAMBO2 device
Turning off the speaker when detecting a Spy Call
Key events are always generated when the device wakes up from Doze mode

Descargas:

Nota: estos documentos sólo están accesibles para usuarios registrados.

Login